Nightwatch Bedbug Monitor Frequently Asked Questions

1. How often should the CO₂ and NightWatch lures be replaced?

The Rhino Power 20 oz CO₂ and NightWatch lure should be replaced after every 7 nights of monitoring.

2. Where can replacement NightWatch lures and Rhino Power CO₂ be bought?

You can buy replacement NightWatch lures from the same distributor or retailer from whom you purchased the NightWatch Bedbug Monitor. Rhino Power can either be purchased from that same distributor or from any Lowe's, Wal-Mart or sporting goods stores that sell paint ball equipment.

3. Where should NightWatch Bedbug Monitor be placed?

All of the research indicates infestations in their early stages are centered around the sleeping area (generally the headboard, pillow, nightstand area) wherever the person normally places their head. Bedbugs are attracted to the CO₂ we exhale.

NightWatch Bedbug Monitors should be placed by the headboard, couch, lounge chairs, futons or wherever people are normally sleeping.

4. A new CO₂ bottle was just installed, the NightWatch was turned on, and the words Low CO₂ are flashing on the screen. What does this mean?

Normally, Low CO₂ warning signals that you have about one day left of monitoring, but in this case, it indicates that the CO₂ bottle has not been tightened enough in the valve. You need to turn the bottle clockwise (to the right) a little more to secure the valve connection.

5. After the first night of use, I have bedbugs in the pitfall traps. What do I do with the bedbugs?

Remove pitfalls on either side of NightWatch using finger holds, lift vertically. Dispose of bedbugs.

Insecticides repel bedbugs. Never allow the NightWatch to become contaminated with insecticide residue. Wash off with soap and water using a damp cloth or sponge. Do not immerse in water.

6. An apartment has been treated 2 times, and people are still getting bitten. What can be done?

It seems likely that the infestation was larger than anticipated, and eggs have hatched producing more bedbugs and tiny nymphs.

Install NightWatch Bedbug Monitor(s) near the sleeping area(s). NightWatch will attract even the smallest first instar bedbug because they all have to feed on blood to grow. If bedbugs are trapped again, contact your professional pest management company. They can perform even more intensive physical inspections, apply additional treatments (chemical, steam, heat, cold) to areas of concern and continue to monitor for an additional 7 to 14 days.

7. Does glue or insecticide need to be placed in the pitfall traps?

No. There is no need to place anything in the pitfall traps. Once bedbugs have fallen into the traps, they cannot climb up the smooth surface to get out. Never contaminate NightWatch with insecticide residue, which is repellent.

8. Can NightWatch be placed directly on a carpeted surface?

Yes. NightWatch can be placed directly on carpeted surfaces. The warmth from the thermal lure would be similar to a pet lying on the carpet at night.

9. Can a person be in the same room with NightWatch Monitor?

Yes. You can sleep in the same room while NightWatch is operating. The NightWatch emits the CO₂ of a child or large household pet. NightWatch attracts bedbugs even if a person is in the same room. Bedbugs will track to what they believe to be the closest host. In this case it could be NightWatch or a person. We recommend isolating the bed from bedbugs with bedpost barriers, treating the bed frame and mattress, and taking care that bed linens do not touch the floor. See NightWatch Operating Manual.

10. How do I start using NightWatch?

Attach the Rhino Power CO₂ bottle by holding NightWatch upside down and twisting bottle tightly into the valve. Turn NightWatch over, place it near the sleeping area, plug in power cord. Red lights will flash. Enter the time of day, making sure you focus on AM or PM. NightWatch will turn itself on automatically at 10:00 pm and shut off at 6:00 AM. Check pitfall traps every morning for presence of bedbugs. See NightWatch Operating Manual.